(固力組)鄭志鈞 特聘教授

 

7
學歷 北卡羅萊納州立大學 / 美國 / 機械工程 / 博士
專長 結構聲學與振動、振動噪音實驗方法、結構最佳化設計、光機電整合技術
分機 33313
E-mail imeccc@ccu.edu.tw
辦公室 系館521
實驗室 工廠202 光機電結構分析實驗室  | 分機:23347
期刊論文

英文期刊

001 1995 R. F. Keltie*, C. C. Cheng, “Vibration Reduction of Mass-loaded Beam,” Journal of Sound and Vibration, Vol. 187(2), pp. 213-p228. (SCI, EI)

 

002 1998 C. C. Cheng*, J. K. Wang, “Structural Acoustic Response Reduction of a Fluid-Loaded Beam Using Unequally-spaced Concentrated Masses,“ Applied Acoustics, Vol. 54(4), pp. 291-303. (SCI, EI)

 

003 1999 C. C. Cheng* and C. M. Chui, “Sound Radiation from Periodically Spring-Supported Beams under the Action of Moving Line Forces,” Journal of Sound and Vibration, Vol. 226(1), pp. 83-99. (SCI, EI)

 

004 2000 C. C. Cheng*, C. P. Kuo and J. W. Yang, “Wavenumber-Harmonic Analysis of a Periodically Supported Beam under the Action of a Convected Loading,” Journal of Vibration and Acoustics, Transactions of the ASME, Vol. 122(3), pp. 272-280. (SCI, EI)

 

005 2001 C. C. Cheng*, and J. S. Shiu, “Transient Vibration Analysis of a High Speed Feed Drive System,” Journal of Sound and Vibration, Vol. 239, n. 3, pp. 489-504. (NSC 88-2622-E-194-003) (SCI, EI)

 

006 2001 C. C. Cheng*, C. P. Kuo and J. W. Yang, “A Note On the Vibro-acoustic Response of a Periodically Supported Beam Subjected to a Convected Loading,” Journal of Sound and Vibration, Vol. 239(3), pp. 531-544. (NSC 89-2212-E-194-010) (SCI, EI)

 

007 2001 C. C. Cheng*, C. P. Kuo and J. W. Yang, “Wave Propagation of a Elastically Supported Fluid-loaded Beam Subjected to a Moving Load,” Journal of Chinese Society of Engineers, Vol. 22, No. 1, pp. 31-39. (NSC88-2212-E-194-004) (EI)

 

008 2001 C. C. Cheng* and P. W. Wang, “Applications of the Impedance Method on Multiple Piezoelectric Actuators Driven Structures,” Journal of Vibration and Acoustics, ASME, Vol. 123. n. 2, pp.262-268. (NSC88-2212-E-194-004) (SCI, EI)

 

009 2002 C. C. Cheng* and J. K. Wang, “Applications of Unequally Spaced Absorbers on Vibro-Acoustic Response Reduction of a Fluid-Loaded Beam,” Journal of Chinese Society of Engineers, Vol. 23, No. 1, pp. 85-91. (NSC86-2221-E-194-030R). (EI)

 

010 2002 K. W. Yang, A. G. Liu, C. C. Cheng* and Y. L. Lo, “Topology and Shape Optimization of Substrate using for Chirp Fiber Bragg Grating Spectrum Tuning,” IEEE/OSA Journal of Lightwave Technology, Vol. 20, No. 7, pp. 1182-1187. (NSC89-2622-L-011-001) (SCI, EI)

 

011 2003 C. C. Cheng* and J. K. Lin, “Modeling of a Rotating Shaft Subjected to a High Speed Moving Force,” Journal of Sound and Vibration, Vol. 261, pp. 955-965. (NSC 89-2212-E-194-010) (SCI, EI)

 

012 2003 C. C. Cheng* and J. Y. Wang, “Free Vibration Analysis of a Resilient Impact Damper,” International Journal of Mechanical Science, Vol. 45, No. 4, pp. 589-604. (NSC 89-2212-E-194-010) (SCI, EI)

 

013 2004 E. M. Chang, C. C. Cheng* and Y. L. Lo, “Thermal Compensation for a Chirp FBG-bonded Substrate,” IEEE, Transactions on Advanced Packaging, Vol. 27, No. 1, 188-193. (NSC89-2622-L-011-001) (SCI, EI)

 

014 2004 U. C. Gu and C. C. Cheng*, “Vibration Analysis of a High-speed Spindle Under the Action of a Moving Mass,” Journal of Sound and Vibration, 278, pp. 1131 - 1146. (NSC 90-2622-E-194-003) (SCI, EI)

 

015 2005 F. T. Wu, K. W. Yang, C. C. Cheng*, F. Y. Lin, K. L. Pan and Y. Y. Chen, “Development of the Methodology to Improve Automotive Door Closing Sound,” IMechE, Part D: Journal of Automobile Engineering, 219, pp. 1 - 10. (SCI)

 

016 2005 C. C. Cheng* and C. C. Lin, “An Impedance Approach for Vibration Response Synthesis Using Multiple PZT Actuators,” Sensors and Actuators A: Physical, 117(3), pp. 480-490. (NSC 90-2622-E-194-003) (SCI)

 

017 2005 C. C. Cheng* and P. W. Wang, “Natural Frequencies Tuning Using Structural Patches,” Journal of Vibration and Acoustics, ASME, Vol. 127, No. 1, pp. 28-35. (NSC 90-2622-E-194-003) (SCI, EI)

 

018 2005 C. C. Cheng* and C. C. Lin, 2005, “An Impedance Approach for Determining Optimal Locations and Shapes of Multiple Induced Strain Actuators,” Smart Materials and Structures, 14, pp. 1120-1126. (NSC 90-2622-E-194-003) (SCI, EI)

 

019 2005 C. C. Cheng*, Y. L. Lo, B. S. Pun, E. M. Chang and W. Y. Li “An Investigation of Bonding Layer Characteristics of a Substrate-Bonded Fiber Bragg Grating,” IEEE/OSA Journal of Lightwave Technology, Vol. 23, No. 11, pp.3907-3915. (NSC89-2622-L-011-001) (SCI, EI)

 

020 2005 C. C. Cheng* and P. W. Wang, “An Impedance Modeling Technique For a Fluid-loaded Structure,” AIAA Journal, Vol. 43, No. 11, pp. 2454-2457. (NSC 91-2212-E-194-020) (SCI, EI)

 

 

021 2006 P. W. Wang and C. C. Cheng*, “Design of Vibration Absorbers Used in Multiple Tonal Excitations,” Journal of Vibration and Acoustics, ASME, Vol. 128, No. 1, pp. 106-114. (NSC 90-2622-E-194-003) (SCI, EI)

 

022 2006 F. T. Wu and C. C. Cheng*, “Design and Analysis of a Speed-Dependent Torsional Vibration Absorber,” IMechE, Part D: Journal of Automobile Engineering, Volume 220, Number 6, 2006, pp. 763-774. (SCI, EI)

 

023 2007 C. C. Cheng*, Y. L. Lo, W. Y. Li, C. T. Kuo and H. C. Cheng, “Estimations of Fiber Bragg Grating Parameters and Strain Gauge Factor Using Optical Spectrum and Strain Distribution Information,” Applied Optics, Vol. 46, Issue 21, pp. 4555-4562. (SCI, EI)

 

024 2007 P. W. Wang and C. C. Cheng*, “A design methodology for multiple tonal beam-type vibration absorber,” Noise & Vibration Worldwide, Vol. 38, No. 10, pp. 11-16. (NSC 90-2622-E-194-003) (Invited paper)

 

025 2008 C. C. Cheng*, F. T. Wu, K. S. Hsu and K. L. Ho, “Design and Analysis of Auto-Balancer of an Optical Disk Drive Using Speed-Dependent Vibration Absorbers,” Journal of Sound and Vibration, Vol. 311, pp. 200–211. (NSC 95-2221-E-061) (SCI, EI)

 

026 2008 C. C. Cheng* and C. C. Lin, “Acoustic Response Synthesis Using Multiple PZT Patches,” Journal of Vibration and Acoustics, ASME, Vol. 130, 011011. (NSC 88-2622-E-194-003) (SCI, EI)

 

027 2008 C. C. Cheng*, T. D. Tsai, D. W. Lin and C. C. Chiu, “Design and Analysis of Shock Absorbing Structure for Flat Panel Display”, IEEE Transactions on Advanced Packaging, Vol. 31, No.1, pp. 135-142. (SCI, EI)

 

028 2008 W. N. Cheng, C. C. Cheng* and G. H. Koopmann, “Dynamic Beam Modification Using Dimples,” Journal of Vibration and Acoustics, ASME, Vol. 130, 041007. (NSC 94-2218-E-194-007) (SCI, EI)

 

029 2009 W. Y. Li, C. C. Cheng* and Y. L. Lo, “Investigation of Strain Transmission of Surface-Bonded FBGs Used as Strain Sensors,” Sensors and Actuators A: Physical, Volume 149, Issue 2, 16 February 2009, pp. 201-207. (NSC 94-2218-E-194-006) (SCI)

 

030 2009 C. C. Cheng*, F. T. Wu and K. L. Ho, “Reduction of Flow-Induced Vibration and Noise of an Optical Disk Drive,” Journal of Sound and Vibration, Journal of Sound and Vibration, 320, pp. 43 - 59. (NSC 95-2221-E-194-061) (SCI, EI)

 

031 2009 C. C. Cheng*, C. P. Kuo, F. C. Wang and W. N. Cheng, “Moving Follower Rest Design Using Vibration Absorbers for Ball Screw Grinding,” Journal of Sound and Vibration, Journal of Sound and Vibration, Vol. 326, pp. 123–136. (SCI, EI)

 

032 2010 F. C. Teng, F. T. Wu, C. C. Cheng* and C. K. Sung, “Design and Analysis of Packaging Boxes for Flat Panel Display,” IEEE Transactions on Advanced Packaging, Vol. 33, No.1, pp. 106-114. (SCI, EI)

 

033 2010 W. Y. Li, C. C. Cheng* and Y. L. Lo, “Accurate Simulations of Reflective Wavelength Spectrum of Surface-Bonded FBG,” Applied Optics, Vol. 49, No.17, pp. 3394-3402. (SCI)

 

034 2010 C. C. Cheng*, C. P. Kuo, F. C. Wang and W. N. Cheng, “Vibration Analysis of Rail Grinding Using a Twin-Wheel Grinder,” Journal of Sound and Vibration, Journal of Sound and Vibration, In press (SCI, EI)

 

035 2010 W. N. Cheng, C. C. Cheng* and G. H. Koopmann, “A New Design Strategy for Minimizing Sound Radiation of Vibrating Beam Using Dimples,” Journal of Vibration and Acoustics, ASME, Accepted for publication. (SCI, EI)

(* 為通訊作者)

中文期刊

 

001 1999 鄭志鈞,楊宗仁”擁有加強樑平板之聲壓輻射分析”,”中國造船暨輪機工程學刊機械月刊,十八卷第二期,文57-67。

 

002 2002 陳建昌、姜冠禎、鄭志鈞,”結構輕量化設計,”機械月刊三月號,二十八卷第三期,文18-28。

 

003 2003 吳豐泰、鄭志鈞,”高速光碟機振動與噪音抑制之研究,”中華民國機構與機器原理學會會刊,十四卷第三期,文32-37。

 

004 2004 何智強、蔡騰德、鄭志鈞,”工具機結構輕量化技術,”機械工業雜誌三月號,252期,166-179。

 

005 2010 王福清、程文男、鄭志鈞,”研磨顫振抑制機構之設計、模擬與分析,” 機械月刊四月號,第417期,文26-42。

研討會論文

001 1996 C. C. Cheng, C. M. Chui, 1996, “Sound Power From Water-Loaded Beams Having Periodical Spring Supports Under the Action of Moving Line Forces,“ 中華民國第二十屆力學會議,pp. 63-68.

002 1996 C. C. Cheng, J. K. Wang, 1996, “Vibro-acoustic Response Reduction of a Fluid-Loaded Beam Using Unequally-spaced Concentrated Masses,“ 中國機械工程學會第十三屆全國學術研討會,pp. 263-271.

003 1997 鄭志鈞、楊宗仁, 1998, “擁有加強樑平板之遠場聲壓分析,” 第五屆三軍官校基礎學術研討會,pp. 4.20-1 – 4.20-8.

004 1997 鄭志鈞、王俊國,1997, “應用不等間距吸震器以減低水中樑的振動聲能,”機械工程學會第十四屆全國學術研討會, pp. 615-622.

005 1997 C. C. Cheng, J. K. Wang, 1997, “Vibro-acoustic Response Reduction of a Fluid-Loaded Beam Using Unequally-spaced Absorbers and Concentrated Masses,“ Journal of Acoustical Society of America, Vol. 101, No. 5, Pt. 2, p. 3062, 133rd ASA Meeting/NOISE-CON ‘97, State College, Pennsylvania, USA.

006 1997 C. C. Cheng, 1997, “Application of Acoustic Reciprocity in Noise PathAnalysis,“ 中華民國第五屆振動與噪音工程學會論文研討會,pp. 3-13.

007 1998 鄭志鈞、楊宗仁,1998, “擁有加強樑平板之聲壓幅射分析,” 中國機械工程學會第十五屆全國學術研討會,pp. 629-636。

008 1998 鄭志鈞,林宏明,1998,“等間距彈性支撐樑在移動負荷下之振動分析,” 中國機械工程學會第十五屆全國學術研討會,pp. 391-398。

009 1999 C. C. Cheng and J. S. Shiu, “Transient Vibration Analysis of a High Speed Feed Drive System,” The 7th National Conference on the Society of Sound and Vibration, Hsin-Chu, Taiwan, R.O.C., pp.120-126.

010 1999 C. C. Cheng, C. P. Kuo and J. W. Yang, “On the Acoustic Response of a Periodically Supported Beam Subjected to Convected Loading,” The 23rd National Conference on Theoretical and Applied Mechanics, Hsin-Chu, Taiwan, R.O.C.

011 1999 C. C. Cheng, C. P. Kuo and J. W. Yang, “Vibration Wavenumber Response of A Periodically Supported Beam Subjected To Moving Forces,” Proceeding of the 16th National Conference of the Chinese Society of Mechanical Engineers, Hsin-Chu, Taiwan,R.O.C., pp. 325-331。

012 2000 C. C. Cheng and K. C. Chiang, “Integration and Applications of a Topology Optimization System in Structural Design, ”Proceeding of the 17th National Conference of the Chinese Society of Mechanical Engineers, Kaohsiung, Taiwan,R.O.C., pp. 801-808.

013 2000 C. C. Cheng and H. S. Lai, “Transient Vibrations of a Rib-stiffened Plate Subjected to a Moving Force,” Proceeding of the 17th National Conference of the Chinese Society of Mechanical Engineers, Kaohsiung, Taiwan, R.O.C., pp. 665-672。

014 2000 C. C. Cheng and J. Y. Wang, “Vibration Analysis of a Resilient Impact Damper,” The 24th National Conference on Theoretical and Applied Mechanics, Taiwan,R.O.C.

015 2000 C. C. Cheng and J. K. Lin, “Study of The Dynamic Response of a Rotating Shaft Subjected To a High Speed Moving Force,” The 24th National Conference on Theoretical and Applied Mechanics, Chung-Li, Taiwan, R.O.C.

016 2001 C. C. Cheng and Y. C. Ku, “Vibration Analysis of a High-speed Spindle Under the Action of a Moving Mass,” The 25th National Conference on Theoretical and Applied Mechanics, Taichung,Taiwan, R.O.C., pp. 2313-2314.

017 2001 M. C. Cheng, R. J. Shyu and C. C. Cheng “Vibro-acoustic Response Analysis and Test Verification for Rocsat-1 Satellite,” The 25th National Conference on Theoretical and Applied Mechanics,Taichung, Taiwan, R.O.C., pp. 2313-2314.

018 2001 C. C. Cheng and A. G. Liu, “Applications of Topology Optimization on Inverse Problems of Strain,” Proceeding of the 18th National Conference of the Chinese Society of Mechanical Engineers, Taiwan, R.O.C.

019 2001 C. C. Cheng and K. S. Lin, “Investigation of Tunnelling Effect In Statistical Energy Analysis,” Proceeding of the 18th National Conference of the Chinese Society of Mechanical Engineers.

020 2001 K. W. Yang, A. G. Liu, C. C. Cheng and L. Y. Lo, ” Topology and Shape Optimization of Substrate using for Chirp Fiber Bragg Grating Spectrum Tuning,” Optics and Photonics Taiwan 2001,Kaohsiung, Taiwan, R.O.C., pp. 576-578.

021 2002 E. M. Chang, C. C. Cheng, L. Y. Lo, P. C. Pang and S. C. Cheng” 光纖布拉格光柵與結構基板間膠結層特性之探討,” Optics and Photonics Taiwan 2002, Taipei,Taiwan, R.O.C.

022 2002 C. C. Lin and C. C. Cheng, “Vibration Response Synthesis using Multiple Piezoelectric Actuators,” Proceeding of the 19th National Conference of the Chinese Society of Mechanical Engineers.

023 2002 F. T. Wu and C. C. Cheng, “Analysis of Dynamic Response of Rotating Circular Plate-Fluid Field Coupled System,” Proceeding of the 19th National Conference of the Chinese Society of Mechanical Engineers.

024 2002 C. C. Chen and C. C. Cheng, “Multi-Stage Topology Optimization Design,” Proceeding of the 19th National Conference of the Chinese Society of Mechanical Engineers.

025 2002 F. T. Wu and C. C. Cheng, “Analysis of Dynamic Response of Rotating Circular Plate-Fluid Field Coupled System,” Proceeding of the 19th National Conference of the Chinese Society of Mechanical Engineers.

026 2002 P. W. Wang and C. C. Cheng “Natural Frequencies Tuning Using Structural Patches,” The 26th National Conference on Theoretical and Applied Mechanics,Taiwan, R.O.C.

027 2002 M. A. Hwang and C. C. Cheng “Vibration Reduction of Mechanical Systems using Impact Dampers,” The 26th National Conference on Theoretical and Applied Mechanics, Taiwan, R.O.C.

028 2002 吳豐泰、楊國偉、鄭志鈞、林峯仰、潘國良、陳豫滎“汽車關門音音品技術之建立,“ The 11th National Conference on the Society of Sound and Vibration, Taipei,Taiwan, R.O.C., pp. 3-13. (優良應用論文獎)

029 2003 E. M. Chang, C. C. Cheng and L. Y. Lo, ”具基板布拉格光纖光柵之溫度補償設計,” Optics and Photonics Taiwan 2003, Taipei, Taiwan, R.O.C.

030 2003 B. S. Pun and C. C. Cheng, ”布拉格光纖光柵加速規之設計與分析,” Optics and Photonics Taiwan 2003, Taipei, Taiwan, R.O.C.

031 2003 P. W. Wang and C. C. Cheng, “應用阻抗法於多頻抑振器之設計,” Proceeding of the 20th National Conference of the Chinese Society of Mechanical Engineers,Taipei, Taiwan.

032 2003 C. C. Lin and C. C. Cheng, “阻抗法於結構聲壓合成之應用,” Proceeding of the 20th National Conference of the Chinese Society of Mechanical Engineers, Taipei,Taiwan.

033 2004 C. C. Cheng and F. T. Wu, “自動調節式扭轉吸振器之設計與分析,” The 12th National Conference on the Society of Sound and Vibration, Keelung, Taiwan,R.O.C.

034 2004 C. C. Cheng, F. T. Wu and K. L. Ho, “Reduction of Flow-induced Vibration and Noise of an Optical Disk Drive,” The 11th International Congress on Sound and Vibration, St. Petersburge, July 5-8, Russia, pp. 3415-3420

035 2004 C. C. Cheng, F. T. Wu and K. L. Ho, “Vibration Reduction of an Optical Disk Drive Using Rotational Vibration Absorbers,” Proceeding of the 21th National Conference of the Chinese Society of Mechanical Engineers, Kaoshiung, Taiwan.

036 2004 C. C. Cheng and W. B. Hwang, “Vibration Analysis of Twin Screw Compressors,” Proceeding of the 21th National Conference of the Chinese Society of Mechanical Engineers, Kaoshiung, Taiwan.

037 2005 C. C. Cheng and P. W. Wang, “An Impedance Modeling Technique of a Fluid-Loaded Structure,” 149th Meeting Acoustical Society of America joint meeting with the Canadian Acoustical Association, Hyatt Regency, Vancouver, Canada, 16-20 May, The Journal of the Acoustical Society of America, pp. 2488, Vol. 117, No. 4, Pt. 2 of 2, April, 2005.

038 2005 C. C. Cheng, C. C. Ho and P. S Wu, “應用拓樸最佳化法於三維動態結構之設計,”The 13th National Conference on the Society of Sound and Vibration, Changhua,Taiwan, R.O.C. (優良學術論文獎)

039 2006 C. C. Cheng, F. T. Wu, K. L. Ho, and K. S. Shiu, “Design and Analysis of Auto-balancer of an Optical Disk Drive Using Rotational Vibration Absorbers,” The 13th International Congress on Sound and Vibration, July 2-6, Vienna, Austria.

040 2006 C. C. Cheng and W. N. Cheng, “Applications of Impedance Method on Syntheses of Structure with slots,” The 30th National Conference on Theoretical and Applied Mechanics, December 15-16, DYU, Changhwa, Taiwan, R.O.C.

041 2006 C. C. Cheng , T. D. Tasi and D.W. Lin, “Applications of Topology Optimization on LCD Crashworthiness Design,” Proceeding of the 23th National Conference of the Chinese Society of Mechanical Engineers, Tainan, Taiwan.

042 2006 C. C. Cheng and W. T. Chern, “Dynamic Analysis and Simulation of Twin Screw Compressor,” Proceeding of the 23th National Conference of the Chinese Society of Mechanical Engineers, Tainan, Taiwan.

043 2007 C. C. Cheng and W. N. Cheng, “Dynamic Structure Modification Using Dents,” The 14th International Congress on Sound and Vibration, July 9-12, Cairns, Australia.

044 2007 C. C. Cheng and M. H. Tsai, “Development of Sound Field Measuring System,” Proceeding of the 24th National Conference of the Chinese Society of Mechanical Engineers, Nov. 23-24, Taoyaun, Taiwan.

045 2007 C. C. Cheng and K. S. Yu, “Development of Fiber Grating Measurement System,” Proceeding of the 24th National Conference of the Chinese Society of Mechanical Engineers, Nov. 23-24, Taoyaun, Taiwan.

046 2007 C. C. Cheng and K. S. Yu, “Development of Fiber Grating Measurement System,” Proceeding of the 24th National Conference of the Chinese Society of Mechanical Engineers, Nov. 23-24, Taoyaun, Taiwan.

047 2008 W. N. Cheng, C. C. Cheng and G. H. Koopmann, “Weak Radiator Design Using Dimples,” 155th Meeting Acoustical Society of America joint meeting with the Euronoise, Palais des Congrés, Paris, France, 29 June - 4 July, The Journal of the Acoustical Society of America, p. 3172, Vol. 123, No. 5, Pt. 2 of 2, May, 2008.

048 2008 C. C. Cheng, F. C. Wang and W. N. Cheng, “Follower Rest Design Using Vibration Absorbers for Ball Screw Grinding,” The 15th International Congress on Sound and Vibration, pp. 2398-2405, July 6-10, July 2008, Daejeon, Korea.

049 2008 C. C. Cheng and F. C. Deng, “防撞結構拓樸最佳化設計技術之研發,” The 32nd National Conference on Theoretical and Applied Mechanics, November 28-29, CCU, Chia-yi, Taiwan, R.O.C.

050 2008 C. C. Cheng and C. C. Chiu, “Vibration Analysis of Twin Screw Compressor,” The 32nd National Conference on Theoretical and Applied Mechanics, November 28-29, CCU, Chia-yi, Taiwan, R.O.C.

051 2008 C. C. Cheng and W. S. Lin, “Development of Vibration Diagnostic System for Gearbox,” The 32nd National Conference on Theoretical and Applied Mechanics, November 28-29, CCU, Chia-yi, Taiwan, R.O.C.

052 2009 C. C. Cheng F.C. Wang, W.N. Cheng, “Vibration analysis of rail grinding with double grinding wheels,” The 33nd National Conference on Theoretical and Applied Mechanics, November 13-14, NUUT, Miao-Li, Taiwan, R.O.C.

053 2009 C. C. Cheng and Y. C. Shiu, “Applications of Topology Optimization on Weak Radiator Design,” Proceeding of the 26th National Conference of the Chinese Society of Mechanical Engineers, Nov. 20-21, Tainan, Taiwan, R.O.C.

054 2009 C. C. Cheng and C. F. Lin, “Applications of Beamforming on Acoustic Holography,” Proceeding of the 26th National Conference of the Chinese Society of Mechanical Engineers, Nov. 20-21, Tainan, Taiwan, R.O.C.

055 2009 C. C. Cheng and W. H. Yang, “Investigations of Correlation between Gear Transmission Error and Gear Vibration,” Proceeding of the 26th National Conference of the Chinese Society of Mechanical Engineers, Nov. 20-21, Tainan, Taiwan, R.O.C.

研發專利

001 2003 鄭志鈞、羅裕龍、劉安吉、鄭旭志、楊國偉 “光纖光柵濾波器,”中華民國發明專利,專利公告號碼:535015。

 

002 2004 鄭志鈞、楊國偉、吳豐泰、林峰仰、潘國良“衝擊音堅實度音質參數之建立方法,”中華民國發明專利,專利公告號碼:593989。

 

003 2005 鄭志鈞、吳豐泰、何冠龍“光碟機碟片旋轉之減振與降低噪音裝置,”中華民國發明專利,專利公告號碼:200514043

 

004 2005 鄭志鈞、顏立永、吳豐泰,“壓縮機之可調式消音減震裝置,”中華民國新型專利,證書號數:M265474

 

005 2006 鄭志鈞、王丕文、吳豐泰、林忠志、吳憲璋,“多頻吸振裝置,”中華民國發明專利,證書號數:I269002。

 

006 2006 鄭志鈞、吳豐泰、何冠龍、王丕文“光碟機之減振裝置,”中華民國發明專利,專利公告號碼:200623057

 

007 2008 鄭志鈞、吳豐泰、王丕文、林忠志、何冠龍,“汽車曲軸扭轉吸振器,”中華民國發明專利,證書號數:I300112,專利公開號:200637985。

 

008 2008 鄭志鈞、王丕文、吳豐泰、林忠志、吳憲璋,“螺桿扭轉吸振器,”中華民國發明專利,專利公開號:200819636

 

009 2009 鄭志鈞、宋震國、吳豐泰、何冠龍、王丕文、李文淵、徐凱軒“光碟機之碟片偏心減振裝置,”中華民國發明專利,專利公開號:200907943.

其他

001 1997 鄭志鈞, “機車引擎活塞動作對噪聲音品影響之分析及測試技術建立”,財團法人車輛研究測試中心委託學術機構研究計劃成果報告,民國86年10月。

 

002 1998 鄭志鈞,”擁有加強樑平板的聲能幅射分析”行政院國家科學委員會專題研究計畫成果報告,NSC 86-2221-E-194-030R,民國87年1月。

 

003 1998 鄭志鈞, 劉德騏, 1998, “馬達振動及噪音防制之設計、製組技術研究與模擬實測驗證分析,” 中山科學研究院委託業(學)界研究計畫成果報告,民國87年5月。

 

004 1998 鄭志鈞,”高速鐵路結構在移動簡諧線力量下其輻射聲能分析”,行政院國家科學委員會專題研究計畫成果報告,NSC87-2212-E-194-019,民國87年11月。

 

005 2000 R. J. Shyu and C. C. Cheng, ”Vibro-acoustic Response of Satellite Structures Using SEA and Its Validity Testing Using Real Satellite Structures,” Final Report to NSPO, Contract No. NSC89-NSPO(A)-PC-FA20-01, April 2001.

 

006 2000 H. T. Yau and C. C. Cheng, ”車燈燈殼與燈座接合之應力與幾何誤差分析,” Final Report to TYC Co., Jan. 2001.

 

007 2000 C. C. Cheng, ” Vibro-acoustic Wavenumber Analysis of a Periodical Supported Beam Subject to a Convected Loading,” Annual Report to the National Science Council, Contract No. NSC89-2212-E-194-010, June 2000.

 

008 2001 C. C. Cheng and T. N. Shiau, ”Research and Development of High-speed and High- Precision Feed Drive System of Machine Tools, ”Annual Report to the National Science Council, Contract No. NSC88-2622-E-194-003, May 2001.

 

009 2002 C. C. Cheng and T. N. Shiau ”Research and Development of High-speed and High- Precision Feed Drive System of Machine Tools, ”Annual Report to the National Science Council, Contract No. 89-2212-E-194-010, May 2002.

 

010 2002 C. C. Cheng and Y. L. Lo ”Research and Development of High-speed and High- Precision Feed Drive System of Machine Tools, ”Annual Report to the National Science Council, Contract No. NSC89-2622-L-011-001, May 2002.

 

011 2003 C. C. Cheng, ”Investigations of Vibro-acoustic Response Reduction of High-speed Optical Disk Drives, ”Annual Report to the National Science Council, Contract No. NSC 90-2622-E-194-003, May 2002.

 

012 2004 C. C. Cheng, ”主軸頭座智慧型輕量化分析技術, ”Annual Report to 財團法人精密機械研究發展中心, March, 2004.

 

013 2005 C. C. Cheng, ” Technology Development of Lightweight Vehicle Structures and Safety Validation,” Annual Report to the National Science Council, Contract No. NSC93-2218-E-194-017, June 2005.

 

014 2005 C. C. Cheng, ” Technology Development of Lightweight Vehicle Structural Design,” Annual Report to the National Science Council, Contract No. NSC93-2218-E-194-018, June 2005.

 

015 2006 C. C. Cheng, ”Technology Development of Lightweight Vehicle Structural Design (II),” Annual Report to the National Science Council, Contract No. NSC94-2218-E-194-007, June 2006.

 

016 2006 C. C. Cheng, ” Technology Development of Lightweight Vehicle Structures and Safety Validation (II),” Annual Report to the National Science Council, Contract No. NSC 94-2218-E-194-006, June 2006.

 

017 2006 C. C. Cheng, ”Developments Vibro-acoustic Response Suppression Techniques for Next Generation Optical Disk Drives (II),” Annual Report to the National Science Council, Contract No. NSC94-2212-E-194-016, June 2006.

 

018 2007 C. C. Cheng, ”Developments Vibro-acoustic Response Suppression Techniques for Next Generation Optical Disk Drives (II),” Annual Report to the National Science Council, Contract No. NSC95-2221-E-194-061, June 2007.

 

019 2007 C. C. Cheng, ”Technology Development of Lightweight Vehicle Structural Design (III),” Annual Report to the National Science Council, Contract No. NSC95-2218-E-194-006, Dec. 2007.

 

020 2007 C. C. Cheng, ”Technology Development of Lightweight Vehicle Structures and Safety Validation (III),” Annual Report to the National Science Council, Contract No. NSC 95-2218-E-194-005, Dec. 2007.

 

021 2007 C. C. Cheng, ”六軸CNC齒輪振動噪音複合檢測機研發(1/2),” Annual Report to the National Science Council, Contract No. NSC 95-2622-E-194-006, Oct. 2007.

 

022 2008 C. C. Cheng, ”防振器測試技術與設備之研發,” Annual Report to the National Science Council, Contract No. NSC 96-2622-E-194 -004 -CC3, May 2008.

 

023 2008 C. C. Cheng, ”Developments Vibro-acoustic Response Suppression Techniques for Next Generation Optical Disk Drives (III),” Annual Report to the National Science Council, Contract No. NSC 96-2221-E-194-027, June 2008.

 

024 2009 C. C. Cheng, ” Modifications of Structural Vrbro-Acoustic Characteristics Using Structural Patches, Dimples and Slots (I),” Annual Report to the National Science Council, Contract No. NSC 97-2221-E-194-016-MY1, June 2009.

 

025 2010 C. C. Cheng, ” The Research and Development of CNC High-speed, High Precision Manufacturing and Smart Condition Monitoring Technlogies,” Annual Report to the National Science Council, Contract No. NSC 98-2622-8-194-003-C1, July 2010.

 

026 2010 C. C. Cheng, ”Modifications of Structural Vrbro-Acoustic Characteristics Using Structural Patches, Dimples and Slots (II),” Annual Report to the National Science Council, Contract No. NSC 97-2221-E-194-016-MY2, June 2010.

執行計畫 研究計畫:

計畫名稱

工作

起訖年月

委託機構

汽車引擎腳結構最佳化 設計技術 主持人   094.07.01~095.12.31 華擎機械股份有限公司
武器結構智慧型輕量化與最佳化分析技術  主持人  94.1.1~94.12.31 國科會
建立螺旋式壓縮機振動力學模型 主持人  94.5.1~96.4.30 復盛股份有限公司
車身結構輕量化技術開發及安全性驗證-總計畫(2/3)  主持人  94.8.1~2006.7.31 國科會
車身結構輕量化技術開發及安全性驗證-子計畫一:汽車結構輕量化設計技術之研發(2/3) 主持人  94.8.1~2006.7.31 國科會
次世代光碟機關鍵技術 研究-子計畫二:次世 代光碟機氣流振噪抑制 技術之研發(1/3) 主持人  94.8.1~95.7.31 國科會
織物變形之信號處理與分析研究開發 主持人  95.4.1~95.11.30 紡織產業綜合研究所
織物變形之信號處理與分析研究開發 共同主持人  95.4~95.11 紡織產業綜合研究所
車身結構輕量化技術開發及安全性驗證-總計畫(3/3) 主持人 95.8.1~96.7.31 國科會
車身結構輕量化技術開發及安全性驗證-子計畫一:汽車結構輕量化設計技術之研發(3/3) 主持人  95.8.1~96.7.31 國科會
次世代光碟關鍵技術研究-子計畫二:次世代光碟機氣流振噪抑制技術之研發(2/3) 主持人  95.8.1~96.10.31 國科會
小產學研究計畫-防振器測試技術與設備之研發  主持人  96.5.1~97.4.30 國科會
小產學研究計畫-防振器測試技術與設備之研發 主持人  96.5.1~97.4.30 杉榮機械公司
次世代光碟機關鍵技術研究-子計畫二:次世代光碟機氣流振噪抑制技術研發(3/3) 主持人  96.8.1~97.7.31 國科會
工具機主軸振動監測軟體開發 主持人   97.5.1~97.12.31 工業技術 研究院
東台精機產學合作計畫 主持人  97.6.1~97.8.31 東台精機股份有限公司
應用結構貼片、凹痕與凹槽於結構振噪特性改良之研究(1/2) 主持人  97.8.1~99.7.31 國科會
高速高精度加工技術暨智慧型偵測系統之研發 主持人  98.5.1~99.4.31 國科會
應用結構貼片、凹痕與 凹槽於結構振噪特性改 良之研究(2/2) 主持人  98.8.1~99.7.31 國科會